一、前言

　　1、 Preface

　　機箱機柜作為重要的供電節點，在使用中有著嚴格的要求，在安裝時也非常重要，而扭力的選擇是非常重要的一項。然而，在實際操作中，如何選擇合適的扭矩成了讓許多人疑惑的問題。因此，本文提供了一份機箱機柜螺絲扭力標準參照表，幫助讀者選擇合適的扭力，確保安裝的穩固性和可靠性。

　　As an important power supply node, the chassis cabinet has strict requirements in use and installation, and the selection of torque is also very important. However, in practical operation, how to choose the appropriate torque has become a question that many people are puzzled about. Therefore, this article provides a reference table for the torque standards of chassis cabinet screws, helping readers choose the appropriate torque to ensure the stability and reliability of installation.

　　二、機箱機柜螺絲扭力標準參照表以下為常見機箱機柜螺絲通用的扭力需求，供參考。

　　2、 The torque standards for chassis and cabinet screws refer to the table below for common torque requirements for chassis and cabinet screws, for reference only.

　　1、M4螺絲需要6-7牛米的扭矩；

　　1. M4 screws require a torque of 6-7 Nm;

　　2、M5螺絲需要10-12牛米的扭矩；

　　2. M5 screws require a torque of 10-12 Nm;

　　3、M6螺絲需要20-23牛米的扭矩；

　　3. M6 screws require a torque of 20-23 Nm;

　　4、M8螺絲需要40-50牛米的扭矩；

　　4. M8 screws require a torque of 40-50 Nm;

　　5、M10螺絲需要70-80牛米的扭矩。當然，具體的扭力選用還要根據不同的情況來選擇，如螺栓的長度、松緊程度等，需要根據實際情況進行調整。

　　5. M10 screws require a torque of 70-80 Nm. Of course, the specific torque selection also depends on different situations, such as the length and tightness of bolts, which need to be adjusted according to the actual situation.

　　三、如何選擇扭力在日常操作中，我們有以下幾種方法來選擇合適的扭力。

　　3、 How to choose the appropriate torque in daily operation? We have the following methods to choose the appropriate torque.

　　1、手感法：即通過手感來判斷。

　　1. Texture method: It is judged by the texture of the hand.

　　2、使用扭矩扳手：機箱機柜螺絲使用扭矩扳手來旋緊，選擇合適的扭力。

　　2. Use a torque wrench: Use a torque wrench to tighten the screws of the chassis and cabinet, and choose the appropriate torque.

　　3、數值法：根據相關資料提供的標準來選擇扭力。推薦使用扭矩扳手進行操作，因為它可以提供更加準確的扭力，可以避免意外情況的出現。

　　3. Numerical method: Select torque based on the standards provided by relevant information. It is recommended to use a torque wrench for operation, as it can provide more accurate torque and avoid unexpected situations.

　　四、注意事項在實際操作中，需要注意以下幾點：

　　4、 In practical operation, the following points need to be noted:

　　1、螺栓的長度：如果螺栓過長，需要加寬扭力范圍。

　　1. Bolt length: If the bolt is too long, the torque range needs to be widened.

　　2、不要超過扭力限制：我們需要根據機箱機柜螺絲扭力標準參照表來選擇合適的扭力，而不應該超出扭力限制，這樣會導致螺絲斷裂或者松動。

　　2. Do not exceed the torque limit: We need to refer to the torque standard table for chassis and cabinet screws to choose the appropriate torque, and should not exceed the torque limit, which may cause screws to break or loosen.

　　3、正確的順序：在進行螺絲旋緊的時候，需要按照規定順序來操作，否則會引起不必要的問題。

　　3. Correct sequence: When tightening screws, it is necessary to follow the prescribed sequence, otherwise it may cause unnecessary problems.

　　5、總結選擇合適的螺絲扭力對于安裝穩固的機箱機柜來說至關重要，需要根據實際情況來進行選擇。本文提供了機箱機柜螺絲扭力標準參照表，希望能夠幫助讀者更好地理解和應用扭力。

　　5. Choosing the appropriate screw torque is crucial for installing a stable chassis cabinet, and the selection should be based on the actual situation. This article provides a reference table for the torque standards of chassis and cabinet screws, hoping to help readers better understand and apply torque.

　　本文由 濟南機箱機柜   友情奉獻.更多有關的知識請點擊  http://www.huannengpower.com/   真誠的態度.為您提供為多維度的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Jinan Chassis Cabinet For more related knowledge, please click http://www.huannengpower.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.